A buyer searching for Lamp Holder is usually trying to stop a bad substitute. Low-voltage distribution gear is specified by the fault level, the current, the poles, and the enclosure it sits in. The notes below are selection criteria for a Lamp Holder. They are not a catalog promise. Confirm every rating on the current datasheet, drawing, or test report for the revision you will receive.
What has to be true of Lamp Holder
Low-voltage distribution gear is specified by the fault level, the current, the poles, and the enclosure it sits in. For a Lamp Holder, start from the duty, then the interface to the rest of the machine or the room, then the document that proves the claim. A lower price that leaves one of those blank is a different product.
Lamp Holder is easy to confuse with Flexible Conduit. If the quote could be read as either, add the line that separates them: the rating, the fitment, or the standard named below. Link the drawing number to that line so receiving inspection can reject the wrong one.
Numbers that change the quote
| Line | What to write for Lamp Holder |
|---|---|
| Coordination | What sits upstream and downstream so the combination is selective. |
| Rated current | Continuous current at the ambient inside the panel. |
| Breaking capacity | The fault current the device must interrupt, in kiloamperes. |
| Poles and trip | Poles, curve or trip unit, and residual current if people are protected. |
| Voltage and frequency | The real mains, single or three phase. |
| Mounting | DIN rail, panel, or a stated enclosure with its IP code. |
How to compare two offers
Lay both quotes for Lamp Holder on one sheet and line up coordination, rated current, and breaking capacity. If a cell is empty, the offer is not finished. Ask for the missing line in writing. When those match, the honest difference is lead time, the test evidence, and who carries the warranty. Do not average a fully specified Lamp Holder with a cheaper line that omitted coordination.
Documents worth having before the deposit
IEC 60947 is the usual family for low-voltage switchgear. Ask which part of it the declaration uses. The file should name Lamp Holder and the revision, not only the supplier’s homepage. A factory quality certificate such as ISO 9001 can sit beside that file. It does not replace it.
Failures that show up after delivery
- Mixing a person-protection device with a plain miniature breaker.
- Cutting an enclosure and assuming the IP code survived.
- Sizing a breaker from the load current and ignoring the fault level.
On a Lamp Holder, the expensive version of the first mistake is discovering it after the goods are in the crate. Put the rejection condition in the purchase order while the supplier can still restate the offer.
A worked RFQ line
Use this shape, then replace the brackets with your duty: “Lamp Holder — Write current, breaking capacity, poles, voltage, and the enclosure code.” That sentence is a template, not a rating of any brand. If a supplier’s datasheet uses different units, convert them onto this sheet so the next offer can be compared.
Where words like RoHS / CE belong
Searches often add a constraint to Lamp Holder: RoHS / CE, or explosion-proof / ATEX. Keep those on this page. RoHS is a material limit. CE is a declaration that lists the rules relied on. Ask for the document that names this part number and revision. ATEX or IECEx is a certificate for a zone, a gas or dust group, and a temperature class. An IP rating does not grant it. Skip the mark if the site is not hazardous. If you need a third constraint, add it as another line on the same drawing. A second URL that only swaps the adjective does not give a buyer a second fact.
Related in this section: how to specify Flexible Conduit.
Questions buyers actually ask
What should an RFQ for Lamp Holder include?
Write current, breaking capacity, poles, voltage, and the enclosure code.
Is a cheaper Lamp Holder the same part?
Only if coordination, rated current, and the documents match. A missing line is a different offer.
Do waterproof, OEM, or IP words need their own page?
No. For Lamp Holder they are extra lines on this specification. Ask for the test or the drawing that gives the word a value.